Swimming Pool Pump Energy Savings

!±8± Swimming Pool Pump Energy Savings

When you bought your swimming pool, you knew the summer fun involved additional costs. First in line is the cost of the pool. Next there is maintenance and pool chemicals. Then you received your summer electric bills.

You cannot eliminate the electric costs of running your pool, but you can minimize them. Swimming pool pumps consume a lot of electricity, second only to home air conditioning. Is your swimming pool pump sized correctly? The larger the pump the greater your maintenance costs will be. Most private residential pools require .75 horsepower pumps or less. Consider the following chart.

Hours .5 HP .75 HP 1 HP 1.5 HP 2 HP
4 70 105 133 184 239
6 105 157 200 276 358
8 140 209 267 368 477
10 174 262 334 460 597
12 209 314 400 552 716

kWh per month - multiply by your electric rate for dollar figure
Source: San Diego Gas & Electric Co.

Reducing the size of your next swimming pool pump by even .25 horsepower will have a significant impact on your electric use. But you say you need a large pump to circulate and filter the water frequently. Generally if your swimming pool water recycles once every 24 hours, it should be adequate.

Many pool owners run the pump much longer than necessary. Four to six hours a day is usually sufficient. Remember you don't have to run the pump constantly for this 4-6 hour period. If you tend to get bugs collecting overnight, run the pump for a few hours at mid-morning then again for a few hours in the afternoon or early evening. In between your filtering, use your skimmer net for any surface debris that gets in.

Make sure to monitor and adjust chemical levels as required. If the water is properly balanced and is still cloudy with your reduced filtering, add filtering time in .5 hour increments until you reach an optimal filtering time. Any amount of filtering time reduced will save you money. It's worth a little trial and error to find your lowest required recirculation time. Do the math, and then save some money.

If your current swimming pool pump is nearing replacement, consider a high efficiency, two speed pump at the correct horsepower rating. With a two speed pump you normally run the pump on low except for vacuuming and backwashing. The low speed is much quieter and consumes much less electricity.

Swimming Pool Pump Energy Savings

Best Prices Zebra Paper Lanterns Ez Cup Keurig Purchase

POOLCENTER.com - Hayward Pool Pump Impeller-Seal Replace 2

!±8± POOLCENTER.com - Hayward Pool Pump Impeller-Seal Replace 2

POOLCENTER.com - Hayward Pool Pump Impeller-Seal Replace 2

POOLCENTER.com - Hayward Pool Pump Impeller-Seal Replace 2

Top 10 Tx-nr3008 Onkyo Dewalt Dw746 Sale Off

Great Tips to Troubleshoot the Hayward Pool Pump

!±8± Great Tips to Troubleshoot the Hayward Pool Pump

You will need the functioning pool filter and the right chemical when you want to maintain clean water in your pool. For this, you consider the Hayward pool pump and filter to keep the water cleans. But, you have to make sure that the pump can work properly. When you face the problems with the device, there are some techniques to troubleshoot it. The followings are some techniques that you can do.

First, you should tighten all the connections of the hose to the pump and the filter. This is done before troubleshooting the Hayward pump or filter that you have. You will find that the dipping hoses might cause the air enters the system. When the air is in the system and the filters operate in a vacuum environment, the malfunction occurs.

Second, you should look the skimmer basket and remove any debris. You might find the debris there. By opening the skimmer lid and pulling out the basket with any debris, you will be able to troubleshoot the problem where if the water enters the pump. After removing the debris, you should run the filter whether this can solve the problem or not.

Third, you should clean the impeller. You will find that this is located in the tube beyond the pump basket. To do it, you must turn the motor off before opening the lid of the pump basket. Then, you should reach the impeller feel any thing that might make this pump part. Then, pull out any debris, leaves or dirt that clogs the impeller. Then, you should replace the lid after you have finished with it.

Fourth, you should backwash or regenerate the Hayward filter. When the Hayward diatomaceous earth (DE) is pumped, it will regenerate the diatomaceous earth that will make the cleaning process better. This is done by repositioning the DE. But, if the filter is a sand filter, you should do a backwash. Make sure that you follow the manufacturer's instructions to ensure that you do the correct things. If you have done with this, you can turn the filter on and find out whether the problem is solved.

Fifth, you should replace the (DE) and clean it. This is done if regenerating the DE cannot solve the problem in your Hayward pump. For this, you should drain it, open the filter up and wash its cartridges or fingers with a garden hose before re assembling the filter. Then, you should add new (DE) through the skimmer if you have finished with the process.

Those are some things you can do to troubleshoot the Hayward pool pump that you have. But, you have to make sure that you do the correct things so that you can use the pump to maintain the cleanliness of the water in your pool.

Great Tips to Troubleshoot the Hayward Pool Pump

Bargain Sale Cajun Electric Smoker

Hayward SUPER II Pool Pump 1.5hp Max Rated SP3010X15AZ

!±8± Hayward SUPER II Pool Pump 1.5hp Max Rated SP3010X15AZ

Brand : Inground Pool Pump | Rate : | Price :
Post Date : Nov 03, 2011 15:51:33 | Usually ships in 1-2 business days

Hayward SUPER II Pool Pump 1.5hp Max Rated# SP3010X15AZA FEW FEATURES: Heavy-duty, high performance motor for quieter, cooler operation Super-size 180 cubic inch basket has extra leaf-holding capacity. Load extender ribbing ensurers free flowing operation Exclusive swing-aside hand knobs make strainer cover removal easy Service-ease design gives simple access to all internal parts See-thru strainer cover lets you see when basket needs cleaning Self-priming (suction lift up to 8' above water level) All components molded of corrosion-proof PermaGlass XL for extra durability and long life This is a high performance, specifically designed pump for the use on in-ground pools, in-ground spas, or fountainsWe are an authorized Hayward dealer, factory sealed merchandise

• Self-Priming (suction lift up to 8' above water level)
• Lexan see thru cover lets you see when the basket needs cleaning
• AO Smith electric-motors 115/230 volts 60hz.
• High Head Pressure pump
• 1 Year Warranty On Motor - 10 Year Warranty on Strainer Housing

Swiffer Coupon Printable Discount